Radiolink Pixhawk Flight Controller
Radiolink Pixhawk Flight Controller 2.4.8 flight controller is a real king of the open source flight controller made by Radiolink. Based on the 3DR Pixhawk, redesigned the circuit after totally understanding the circuit design and program code of Pixhawk, which guarantees the quality of the product. Achieved less interference of inner components, less noise, more accurate compass and safety while flying.
Radiolink Pixhawk complete automatic, anti-static from SMT to welding achieved less interference of inner components. Full mechanical, anti-static fully automated welding from patch to backhand welding, to achieve reducing interference of geomagnetic sensors, which greatly improves the efficiency of production inspection.
All the chips such as processors, sensors and others are imported with the whole package by the primary agency. The dust-free and environmentally-friendly workshop ensures its durability. Radiolink Pixhawk Flight Controller FPV RC Drone FC 32 Bit with Power Module for Long-wheelbase Quadcopter/6-8 Axis Multirotor
Note: Pixhawk can flash firmware and setup parameters with the official Mission Planner downloaded via https://firmware.ardupilot.org/Tools/MissionPlanner/MissionPlanner-latest.msi
Radiolink Pixhawk User Manual here
To watch more about our products, please visit our YouTube Channel
Pixhawk 2.4.8 Parameters
- Weight & Dimension
- Dimension: 82.2*51.8*16.5 mm(3.2″*2″*0.65″)
- Weight: 38g(1.34oz, PIXHAWK only)
Hardware Specification
Main Processor: STM32F427VIT6
Coprocessor: STM32F100C8T6
Sensor
Gyro: MPU6000
compass: QMC5883L
Barometer: MS5611
Port: XH socket
SPK/DSM: 1
Mavlink UART: 2 (with CTSRTS)
USB Port: 2
BUZZER: 1
SWITCH: 1
ADC Port: 3.3V*1&6.6V*1
SERIAL4/5 Port: 1
GPS UART: 1
CAN Port: 1
SPI Port: 1
I2C Port: 1
RC In(TX Signal Supported): SBUS/PPM
RSSI signal Strength Input: PWM/3.3V
PWM Output: 8 OneShot/PWM Output (Configurable)
Aux Output: 6 PWM Output (Configurable)
SD Card Port: 1
Power Module Specifications
Input Voltage: 2-8S
Input Current: 90A
Output Voltage: 5.1V
Output Current: 2A
Input Current : (connect to one ESC only): 90A
Adaptable Models
Rotary/3-8 copter/Fixed Wing/VTOL/Car/Boat/Robot/Mower
Specifications
USB Voltage: 5V±0.3V
Operating Temperature: -40~80℃
Advice
For first-time Pixhawk users, follow these setup steps.
First, install Mission Planner and its driver from the provided link. Take time to get familiar with the software menu.
Next, select your preferred communication channel to build a link. After that, set up physical hardware and Windows device drivers. You may connect the autopilot to your PC via USB, telemetry radio, Bluetooth or IP.
Then, download the latest firmware over USB if an update is required.
Subsequently, link Mission Planner to the autopilot. Afterward, plug your receiver into the autopilot to calibrate your transmitter, accelerometer and compass.
Next, configure flight modes on your RC transmitter.
After that, assemble your airframe completely. Be sure to go through every item on the pre-flight checklist.
Then, tune and apply your PID parameters.
Finally, carry out extra advanced configurations for your specific needs.
Connectors



For using the Radiolink Pixhawk APM PX4 Flight Controller, please also buy SE100 M8N GPS






























Seongho Kim (verified owner) –
Great little package to start flying on Pixhawk.The perfect option for diy drones!
Christy (verified owner) –
This is my first experience with Pixhawk and I love it. It has tons of features and very accurate response.